Applications

APPLICATIONS

From micro dispensing in consumer electronics to high-flow potting in new energy, our components keep your process stable.

Browse by industry

INDUSTRY SCENARIOS

Six industry scenarios and matching solutions

See typical workpieces, process challenges and recommended valves by industry to align selection fast.

Consumer electronics

Dot, line and area coating for phones, wearables and acoustic parts.

Typical workpieces: Mid-frame parts, camera modules, acoustic components, TWS housings
Process challenges: Narrow gaps, tiny volumes (0.005–0.05 mL), risk of overflow and stringing, long continuous runs.
AIMTE solution: Positive-displacement screw valve with fine needles replacing time-pressure control, plus regulated supply to cut first/last dot deviation.

Recommended lines Screw Valve Dispensing Valve

Semiconductor & packaging

Underfill, package dispensing and interface materials.

Typical workpieces: BGA / CSP chips, package substrates, power devices
Process challenges: Underfill needs high consistency and no voids, tight cycle time and frequent changeovers.
AIMTE solution: Servo dispensing module for stable pressure, paired with screw valves for repeatable volume and regulated supply to suppress voids.

Recommended lines Servo Dispensing Module Screw Valve

New energy & storage

Structural adhesives, module potting and thermal gels.

Typical workpieces: Battery cells, modules, CCS busbars, storage packs
Process challenges: Filled high-viscosity fluids, medium-high continuous flow, long feed lines, hard to hold volume and ratio stability.
AIMTE solution: Supply system with high-flow screw valves, drum pumps for continuous regulated feed, and a distributing machine for multi-point synchronous output.

Recommended lines Glue Supply System Screw Valve Glue Distributing Machine

Automotive electronics

Sealing and potting for sensors, controllers and lamps.

Typical workpieces: Pressure / temperature sensors, ECU units, lamp modules, harness connectors
Process challenges: Large potting volumes, high sealing demands, wide temperature range and vibration, strict batch consistency.
AIMTE solution: Pneumatic valves for high-flow switching with suck-back to stop dripping and stringing, plus regulated supply for uniform fill.

Recommended lines Pneumatic Valve Glue Supply System

Medical & consumables

Reagent filling, catheter bonding and micro-volume dispensing.

Typical workpieces: Reagent cartridges, diagnostic consumables, catheters, microfluidic chips
Process challenges: Micro-litre volumes, high accuracy, expensive fluids, no waste or cross contamination allowed.
AIMTE solution: Micro screw valve with level-sensor closed loop for volumetric output, and easy-clean flow paths to cut changeover waste.

Recommended lines Screw Valve Sensor

Optoelectronics & display

LED packaging, display bezel and optical module bonding.

Typical workpieces: LED modules, display bezels, lenses, optical modules
Process challenges: Long bead paths need uniform coating, edges tend to string, bead width and height must stay stable.
AIMTE solution: Precision dispensing valves with suck-back and servo three-axis motion for uniform coating, plus a distributing machine for multi-station sync.

Recommended lines Dispensing Valve Glue Distributing Machine

SELECTION GUIDE

Selection matrix by process condition

Start with viscosity, shot volume and accuracy; then cycle time and drive type; finally confirm the valve.

Viscosity	Shot volume	Accuracy	Cycle time	Recommended valve	Drive
Low viscosity (< 500 mPa·s)	0.005 – 0.05 mL	± 2%	0.3 – 1 s / dot	AMT-SV05 mini screw valve	Stepper direct drive
Medium viscosity (500 – 50,000 mPa·s)	0.02 – 0.5 mL	± 1%	0.2 – 0.8 s / dot	AMT-SV15 standard screw valve	Servo motor + regulated supply
High viscosity (50,000 – 200,000 mPa·s)	0.1 – 2 mL	± 1%	0.5 – 2 s / dot	AMT-SV35 high-flow screw valve	Servo + drum pump feed
Filled / thermal conductive	1 – 10 mL	± 3%	1 – 3 s / dot	AMT-PV30 high-flow pneumatic valve	Pneumatic + regulated supply
Coating / long bead path	5 – 30 mg/mm continuous	Uniformity ± 3%	50 – 300 mm/s	AMT-DV12 precision spray / dispense valve	Servo 3-axis motion
Micro-litre filling	0.001 – 0.02 mL	± 1%	0.5 – 1.5 s / dot	Mini screw valve + AMT-LS10 level sensor	Servo closed-loop metering

This matrix is a rule-of-thumb range; final selection depends on fluid brand and model, filler size and tubing conditions.

CUSTOM SOLUTIONS

Need part selection, or a custom dispensing solution?

Describe your fluid, process and cycle-time requirements — an AIMTE engineer will come back within 48 hours with a selection proposal and sampling plan.

Proposal in 48 hours
Free sample validation
One-on-one engineer

Or call 189 2849 2979